Showing posts with label BAMA. Show all posts
Showing posts with label BAMA. Show all posts

Sunday, June 28, 2026

Ponies and Snakes 2026

I've been working on a lot of different projects over the past six weeks or so, but nothing that has reached what you might call reporting status. Until this Sunday, which was the Bay Area Mustang Association's most recent edition of the annual Ponies and Snakes car show. Putting on the show is a lot of work - it really does take a village - and BAMA stepped up again. One of the best features of the showground is all the trees and the shade they provide; unfortunately this has a negative impact on the quality of the photos.























Sunday, November 9, 2025

Autolite/Motorcraft 2100 Carburetor Rebuild

The engine swap in the '67 F250 is essentially complete, but I have been struggling to get the timing and the vacuum advance dialed in...and the motor is running very rich. I had a friend from BAMA come by to try and help me, and it became obvious that the carburetor wasn't performing as it should and would need more than minor adjustment.

The carburetor is a Ford branded 2100 model, either Autolite or Motorcraft, and has two barrels. This is a very common carburetor and finding a rebuild kit was easy.


The first step is taking the carburetor apart so that all the parts will fit into a one (1) gallon paint can. I took a lot of photos while I was doing this...


Following disassembly, every single part, screw, nut and spring was soaked for 48 hours in the GUNK™ parts cleaner solution.


After soaking, further cleaning/scrubbing with warm soapy water, rinsing and drying with compressed air:


Ready for reassembly:


All the gaskets and other small parts are available in a kit. Even so, I was careful not to throw away any of the original parts.


I've never rebuilt a carburetor before, so I found an appropriate tutorial on youtube and followed that. Part way through I realized that my carb was missing the primary float assist spring, which does not come with the rebuild kit. The absence of this spring could well be the cause of my problem because without it the float position cannot be set, never mind set accurately. This is yet another issue with the F250 which makes my original successful journey home all the more remarkable. 

The photo below shows what a primary float assist spring looks like; this one came mail order, so the rebuild was on hold for over a week.


Autolite 2100 after rebuild: 


I'm taking the opportunity to replace the throttle linkage since the threads a stripped out on the old one. 


The replacement is adjustable - I chopped 3/4 of an inch off one end to replicate the old part:


This is after re-installation of the carburetor...


....and the new throttle linkage:


The big picture, after I installed the new blue spark plug wires:


I actually had a serious issue with the carburetor after the rebuild - while fuel was getting into the float bowl, it wasn't getting any further. The route to diagnosing this issue was starting fluid: when the fluid was squirted into the business end of the carb, the motor fired right up....but without starting fluid, well, no dice.

After some back and forth, I decided to send the carburetor away for a professional rebuild. It turned out that my carb was not ideal for the manifold/engine combination I have, so I purchased one that was. The next picture shows how the replacement carb looks after installation and connection of the fuel lines and throttle linkage etc. With the new carburetor dialed in, it was straightforward to set the engine timing and the vacuum advance. 



I have a chrome air cleaner which either came off the Mustang or came from one of the guys in BAMA and I purchased an appropriate "302" decal from NPD.  


Air cleaner installed:


This is how the engine sounds with a very dodgy exhaust. Hopefully it will get me to the muffler shop!

Saturday, November 8, 2025

BAMA Trip to Arnold, CA

Round, round, get around, I get around....We were only just unpacked from the Southern States tour when it was time to head out to Arnold, CA with the folks from BAMA.

The first stop was the Angels Camp Museum & Carriage House, in Angels Camp CA.










Stevenot Winery in Murphys, CA: 


We stayed at the Black Bear Inn in Arnold, CA. BAMA booked out all the rooms so we had exclusive use of the lounge areas and patio, hot tub etc.



Day two at the Sierra Logging Museum, just up the road from Arnold, CA




The (not very) imaginatively named White Pines Lake is right next to the logging museum.


Hanging out and gambling at the Black Bear Inn: