Showing posts with label woodwork. Show all posts
Showing posts with label woodwork. Show all posts

Friday, November 20, 2026

History of the Workshop(s)

I've written many times in this blog about how fortunate I am to have the perfect, all-purpose workshop for all my tools and a double garage for the automotive projects. Beyond the size of the workshop, the best feature is the window which looks out onto the backyard. This post was intended to document converting the window into an exterior door, and the importance of installing a glazed door....but then I started thinking about all the different "shops" I've had since I moved to the USA and they didn't all have natural light....

The first 'shop, if you can call it that, was in the basement of our rental house in the posh part of Berkeley. Space was at a premium, so it was just my old ikea desk, a crappy chest of drawers with a bookshelf on top, and some tools hung on the wall. There were no windows in the basement, but it did have an exterior door which could be left open for some natural light.  


This was when I started acquiring tools...


Workshop number two was the double garage when I lived in the Oakland hills the first time round. The two timber benches that I still have were built to fit into this garage.

I imported some toolboxes from the motherland in 2008, which has been well documented in this blog. The tools below came with them. I was proud off my hand tool collection at the time. This saw can be seen in the top left.

The garage had a huge rear-facing window with a beautiful view of the hillside: 


I got my first table saw during this period.


The space became very cramped after I bought the '68 Mustang coupe:

The next stop was what became known as the Green Room, for obvious reasons. I had a very nice setup in this garage, and although it did have a window and a glazed door, I covered them both up for total privacy. I didn't really do anything apart from work on the car in this garage; the table saw was never put together. 



I was only based at the Green Room for about fourteen (14) months, but I spent a LOT of that time working on the Mustang. The photo below, which is still one my favorite pictures of the car, was taken in this garage. When I bought my Mustang, I put all the money into getting a really good body shell, because I didn't want to do any significant welding. It turns out this was a smart move, because everything else has been replaced at this point, some things more than once.


The next two photos were taken the day I moved out of the Green Room; the '68 went a day or two after everything else. As you can see, still no engine...



Workshop #4 was a deep single-width garage a few blocks from Pixar. The next two photos show the garage after the first batch of "stuff" was moved from the Green Room, and after the Mustang and the second batch were transferred:



It took many months to convert the garage into a space I could work in, but in the end, I had a nice little setup. Again, no table saw, and no natural light, by default this time.



This garage was always cramped, but I did a lot more work on the car here and I had some memorable times, including dropping in the V8 with the transmission attached. The first time.


The car didn't look that different on moving day, but in addition to the drivetrain it has been completely re-wired at this point, the front end has been replaced and most of the dash and interior components have been re-installed.

The fifth workshop consisted of two (2) distinct entities. The '68 went to a double-width rental garage on Channing Way in downtown Berkeley. The lighting in this garage was never great and there was no natural light. I had the car on one side and a workbench and my tools on the other side. 

This garage was never my favorite place for a number of reasons: I wasn't supposed to be working on a car in there at all, so I had to be as quiet as possible, and there was no sink or bathroom nearby. Having said that, I got a lot of work done while the car was in this location, including reinstalling the windshield and back glass - with some help from Amy Sheep. When it was time to move on, the car was running, the only problem was I didn't have anywhere to move it to. I ended up putting the '68 into storage out by Oakland airport; it was gone almost a year before we bought our current house, back in the Oakland hills.


While the Mustang was sitting three (3) blocks away, Amy and I built a 16' x 12' shed/workshop at the end of our backyard. The shed did get windows eventually, but there don't seem to be any surviving photos to prove it. 


The shed was a mixture of workspace and storage:



The table saw was finally reassembled but anything long had to be cut with the shed door open. And the shed was never connected to the grid, so lights and power tools had to be run from an extension cord. 

All of which makes the current setup workshop #6:




And garage #5 (or #6 if you count the term in storage):


Wednesday, November 4, 2026

Table Saw Room Refinements Part 4

Earlier this year I built some display cabinets in the table saw room. Some of the cabinets are reserved for storage, and therefore need some doors, otherwise they're just shelves. I've had a few ideas for door designs, but in the end, I decided to return to the concept I came up with for the router table cabinet. This decision means I can make the doors without having to buy any material.

The door frames will be made from red oak. The source of the longer pieces was a hideous 80's TV cabinet that the former owner of my house left behind, and the rest were miscellaneous scraps. I ripped all the bulk material into 1-3/4" wide strips on the table saw. There is some variation in the thickness of oak, so I made pairs of thick and thin strips of similar length. 



Both mating surfaces were planed to remove the old finish, and then wood glue was applied to both sides of the joint:


Everything was clamped overnight:



The glued material is now close to 1-3/4" x 1-1/2".


Face sides and face edges were established at the jointer...


Material was trimmed on the table saw...


And planed on all four sides:


The final dimensions are close to 1-1/2" x 1".


A rabbit which measures 3/4" x 1/4" was cut into the least attractive edge/face:


I figured the easiest way to get all six doors exactly the same size and shape would be to build a jig. The final size of each door is intended to be 30" x 15-1/16", so I constructed a frame that is about six inches longer than that and the exact width:


This is how the jig looks when it has been loaded with the four mitered frame pieces. The fourth side of the jig is installed with two (2) screws, so it can easily be removed. This is important for getting the completed door out of the jig...


I want to dry fit the inset panel before I glue up the frame, so I moved back over to the table saw. I'm making the panels from leftover walnut veneered plywood. I have enough plywood to make the six (6) panels I need, if I ignore the grain pattern. However, the best way to exploit the grain pattern would be to make two pairs of doors....and do something different for the third pair. 


Panel loaded into jig:


After removing all the components, applying glue to the mating surfaces, and reloading the jig, I was ready to install V-nails at the corners of the frame:


I put three V-nails into each corner, and then the door was removed from the jig, and the central panel was clamped to the frame overnight.


The almost finished door looks like the photo below. I need to do some sanding, and I need to make the beading I'm planning to install at the doors.


But, if you've ever read this blog before, you'll already know that I really do not enjoy sanding. So, I moved on to making the final pair of door panels. The concept is basic: the best bits of the remaining walnut plywood separated with some 3/4" wide strips of maple:


The panels were glued-up overnight:


After trimming and sanding off glue residue (below). The outer walnut strips were cut slightly wider than the inner pair. This is because the perimeter of the panel will be obscured by a combination of the edge of the oak frame and the beading; the strips should appear to be of identical width when the door is assembled.


These frames were constructed just like the others, and the panels were glued and clamped overnight:


The last thing to make is the beading, which comes from more scrap red oak. To start with I cut a bunch of 5/16" square strips on the table saw: 


To shape the beading I am using a 3/8" coving bit on the router table, but the size of the red oak stock is too small to pass it safely across the bit..


I cut a 5/16" square recess into a piece of scrap plywood...


..and clamped it in front of the router bit. I can now feed my material through the gap in relative safety:


A total of four passes across the router table were needed to achieve the profile below which is not symmetrical by design. 


As mentioned, the beading is 5/16" wide, but the recess it will be going into is only 1/4" deep. This means that there is 1/16" of material to sand off after the beading is installed. It also means that the profile of the beading will end up being symmetrical or pretty close to it. This overall process gives a much better result than trying to cut beading to 1/4" square in the first instance.


Post beading install, sanding, wood filler, final sanding, more sanding etc.


Finishing with Danish oil, starting with the back of each door:


Fronts finished:


Each door needs six (6) small holes for the hinges and one (1) 3/16" diameter hole for the pull. I made some jigs out of scrap plywood which made this process quick, easy and accurate: 


Cabinet doors installed: 



The big picture: