Showing posts with label bench. Show all posts
Showing posts with label bench. Show all posts

Saturday, October 21, 2023

From The Archives #2 - The Original Workbench

Originally published between 2008-02-21 and 2008-04-14

It's worth pointing out that in the original version of this series of posts the story was told entirely visually; to reduce the overall length a number of photos have been replaced with brief comments. At the time I had a circular saw, a spirt level, two very large C-clamps, a set of chisels, a cordless drill/screwdriver, some pipe clamps and not a lot else; by the end I had acquired an antique Craftsman table saw.

I'm building with a selection of 2"x 4", 4"x 4", and 4"x 6" doug fir 

Sam was on hand to provide encouragement..

started by attaching some 2x4 material to the garage wall. 

lumber was milled with the circular saw and...

...a hammer and chisel.

Then rinse...

...and repeat.

one of many vertical members.

started constructing the bench out from the wall

this is a number of weekends later...

...and several more.

added framing to support shelves.

plywood shelving added

constructed a tool well at the rear

added blocking and framed out the central recess

finished apart from the bench top
 
the bench top was made from 2" x 6" doug fir

secured with screws into the supporting structure

similar material added to the central recess

imperfections were filled and sanded

put on several coats of polyurethane

added oak trim at the perimeter

mounted my first sheet of peg board

Done!

Sam was impressed!

Wednesday, October 11, 2023

Grinding On

Below is a photo of my bench grinder - it's a simple six inch diameter two disc set made by Delta - located between my Wilton vise and the spray booth. The bench grinder was actually a gift from a former relative, and it has served me very well since 2008. But I'm a bit lazy and prefer not to have to change the discs if I can help it. Or to put that another way, I really wanted a second bench grinder, so that I could have simultaneous access to a polishing wheel, a wire brush and a grinding wheel or two without faffing about.   

The six inch diameter wheels suit my needs pretty well, so I decided to just get another grinder the same size. Delta have made some modifications to the grinder in the last fifteen years, which we'll get to in a bit. Firstly though, I need to make space for it. There would have been plenty of space next to the existing grinder in the area where I built the paint booth. So, I just wound back the clock to 2020 and I was done: 


LOL.....not really. For one thing, I don't want to lose my paint booth. Incidentally, one of my mates, we'll call him Dave Pacific Gas, pointed out the other day that the "futuristic" inventions we were all promised as kids have mostly come true, except two things. That's right, we might have video phones, the internet and remote control weaponry, but we're still waiting for flying cars and time travel!

Fortunately, there was a solution on hand, and it started with removing the old grinder and the vise, and ripping the boards off the top:


I followed that by beefing up the left side support - this will be the approximately central support at the extended bench:


The is with the third "leg" constructed but not quite attached:


The aged redwood boards I ripped off were trimmed by a couple of inches, so they end at the center of the middle support, and I still had two of the older boards in the shop. I filled in the space with some scraps of modern redwood. I did think about sanding down the whole bench top and refinishing it with polyurethane... 


Instead, I went upstairs for a cup of Rosie, and managed to regain my composure. Then I went back downstairs and re-installed the original bench grinder in the same place, added the new one, and mounted the vise at the end.


So....what improvements/differences are there between the new grinder and the old one? The most obvious is the shape of the base - the older model has a hexagonal base and two mounting holes...


....while the new model has a rectangular shape and takes four bolts to secure it. The new model also has a small tray at the front which can be filled with water and then used to cool item(s) being worked on. A nice feature, but it would only be useful for small items.


The older model has dust guards which can be lifted out of the way for larger work pieces or when you need to get a good look at what you're doing...


...the dust guards are fixed with the newer version, which is annoying but probably safer...unless they get taken off completely. The model # and what not is also clearly visible on the new grinder. I had to unbolt the old one from the bench top to access this information. 


The older model had what Delta calls "quick release technology" for changing the wheels. Basically, the guard piece is held on with one thumbscrew, and the "nut" which holds the wheel can be flipped and removed by hand:



Delta no longer provides this feature, so the new one has the old fashioned setup: you have to remove three screws and break out the 3/4 inch wrench to change the wheels on this one. The thing is, I could never be bothered to change the wheels anyway, hence the need to buy a second grinder. In fact, isn't this where we started..... 

Friday, October 6, 2023

The Joy of (Restoring) Tools

I imported the five screwdrivers below with the tool chests I talked about here, in April 2008. They have been in quite a few different garages and basements since then. I've always intended to restore them. This post is the story of how that intention became a reality.


First, let's take a quick look at the damage. Each screwdriver consists of three parts: The steel shaft, the wood handle and a steel ferrule: 


 Most of the steel shafts were bent....


Or have chipped ends....


And the handles have been lightly mushroomed...


The first step was getting the shaft straight (ooh, err), which I accomplished by applying appropriate blows with the nearest BFH. This was followed by a good going over with the wire wheel:


This revealed the "GTL" logo on the smallest and largest screwdrivers, which indicate they came from my Uncle Herbert's tool chest:


Next, I used a combination of the grinding wheel and a flat file to hone the business end of the screwdriver shaft into a symmetrical and square blade:


The flat blade and the shaft took a lot of sanding. I started with 100 grit emery cloth which was enough to work out most of the divots - the next photo is taken part way through this process. 


This is later after a lot of sanding, working through the grits...150, 240 and 400. This was the most laborious part of the process.


Same again with the ferrule...the smaller ones were more difficult /fiddly to work on. 


The wood handles were re-rounded with a flat file and the entire handle was sanded with 150 grit all over....and then I worked through the grits as above to 400. 


The grooves in the handles were cleaned out with abrasive thread which I sourced online for this specific purpose.


There were a few dings in the handles that were too serious to sand out: 


I made some filler out of sanding dust and wood glue and applied it to the most serious defects in the handles:


More sanding of the metal parts to 600 grit with "wet 'n 'dry," polishing of the metal parts, finishing of the handles with Odies hard wax and then reassembly gives the result below. As I mentioned, the largest and smallest screwdrivers date from my Uncle's tool chest. Two of the others have the word "Halford" on the shaft which is the hallmark of mass production and the fifth is just "British made."


I also have possession of Uncle Herbert's tenon saw, which did not come out of the tool chest. This is my primary hand saw and always has been. I don't use it much, what with having so many power tools, but when I need a hand saw I use this one. It cuts great and doesn't need sharpening. But it does look a bit beaten up:



On close inspection I discovered the wood handle was cracked. This has never affected the functionality.


Getting the handle off was straightforward and revealed some rust at the previously hidden section of the saw blade. 


I sanded the blade and the brass casing with 400 grit while trying to keep away from the teeth:


The manufacture's information is much clearer now: "Fredrick Willey, Leeds; Cast Steel - Warranted."


The saw handle was sanded and then refinished in the same way as the screwdriver handles. 


Reassembled: