Showing posts with label chainsaw. Show all posts
Showing posts with label chainsaw. Show all posts

Thursday, December 17, 2020

Front Yard part five

We're going to have a fence installed at the perimeter of the yard where the raised beds are located - we lost too many plants to predators last year to ignore them any longer.  I say "have" a fence installed, because I don't feel like doing it myself! 

Before we can install the fence, we have to figure out exactly where we want to put it. We planned ahead and called those fire-starting, ill-prepared very nice folks at PG&E, and they came by and marked the location of the gas line. This was fortunate, because the gas pipe runs very close to where we were thinking of putting the fence.

After the gas line, the next biggest obstacle was the brick patio in front of the house. Eventually the whole patio is going to do one, but for now we just need to get rid of the two (2) feet furthest from the porch. 

It was pretty obvious that the bricks had been installed on top of a concrete pad - it wasn't exactly clear how deep the concrete was, or whether it was solid - I was hoping it might just be a concrete perimeter...

We started chipping away at the brickwork...it soon became apparent that the concrete was a thick slab all the way through....this means more effort to break it up and more broken concrete to get rid of.



This is after about 45 minutes of breaking off bricks and, mostly, pieces of bricks, with the spike attachment on the jackhammer. It might look sunny in these photos, but it was less than 50F/10C and there was a strong wind.


After cleanup phase #1 and a quick raid attack on the thinnest corner of the slab, I was relieved to discover there was essentially no rebar in the concrete.


Breaking up the thicker side of the slab required quite a bit more effort so I handed the jackhammer over to Amy Sheep. 


All done! Well sort of....we've removed about two (2) feet of the patio. There's at least another fifteen feet to go, but I have a feeling we won't be doing any more of it ourselves. The fence can now go in between the remaining section of the patio and the gas line which is marked with the yellow flag in the photo below.


In addition to all the debris strewn around in the above photo, we filled ten five-gallon buckets with broken up masonry.


After lunch we carted all the debris over to the driveway. Then we filled in the hole and smoothed out the dirt between the remaining patio and the raised beds.


That just left a tree stump to get rid of...it looked pretty small at first...


Looking quite a bit bigger after a hour or so alternating between the spade, the trowel, the jackhammer and the circular saw... 


Finished it off with the chain saw and my sledge hammer. Now we just need to put the fence up.


Monday, November 23, 2020

Bye Bye Pine Tree

We used to have a huge pine tree in front of the house. For the last three years it's been dropping sap on our cars and carpeting the yard and driveway with needles. What's more, the extensive root system was in the way of our driveway expansion plans. I thought long and hard about taking the tree out myself, but I figured it would take me the entire weekend just to cut it down, never mind chop up the wood, get rid of all the branches, and grind out the stump......and the tree was very close to the power lines. So I waved my checkbook at the problem, and the crew we hired took care of the whole process in less than five hours:







Sunday, May 31, 2020

Garden Shed part two

Two weekends ago, or a fortnight in Ye Olde English, The Amy Sheep and myself removed a thirty (30) foot tree from the spot where we want to build our new shed. What we left was the stump, and as longer term followers of this blog might recall, we've dealt with one of those before.

This time round we didn't want to rent the big stump grinder: it would be very difficult to get it down the slope to where we need it, and we don't have the budget for this project - the last stump was five feet in diameter, so we didn't have a choice with that one. 

Plan A was to rent a smaller stump grinder for considerably less wonga. This didn't go to well sadly: the stump grinder was pitifully weak and the motor kept cutting out. After messing about with it for half an hour I bailed and returned it. The motor issue was a convenient excuse to get my $$$ back frankly.

Onto plan B, which was a star wedge and the BFH. This plan lasted about 29 minutes less than plan A.


Plan C was for Amy Sheep to dig out the stump.....this went the same way as Plans A and B, but it did clear the path for Plan D.


And Plan D was the chainsaw....


We were definitely onto something this time....


This plan was carried out in full:


The stump was our last obstacle to world domination what will be our new tool shed. But, before we can build the shed, we need a level playing field. Or at least a level pad slightly bigger than the shed's 8' x 4' footprint. The ground in this area is drops about five (5) inches from the right rear to front left. We used some 6" x 4" "pressure treated" (PT) timber to build a retaining barrier for the foundation. This is timber that has been treated with wood-preserving chemicals under high pressure, and is thus highly resistant to fungus, termites etc. This is important for any timber which is in contact with the ground. 

The first piece was installed level, and parallel to the fence - getting it level took a little bit of back-and-forth. I anchored the timber with several two foot pieces of 1/2 inch diameter rebar which were deployed with the BFH: 


The holes were drilled with this tasty bit of kit:


A second retaining barrier was added at the low side...


And then we laid down some base rock - or road base, as it's known some parts of the country. This is material that varies in size from half inch diameter down to sand and is very easy to compact.


We tried to rent a compactor, but we couldn't find one locally, so I had Amy Sheep do it instead with a scrap of 4" x 6" lumber. After that we had to cash out our chips for the day.


The next morning, after a quick trip to pick up more base rock, we set about leveling out the pad.


The next step was to cut and install the skids that the shed will stand on. The skids were cut from 8' lengths of 4" x 4" PT, and we used all six pieces although five would probably have been enough. 


The first skid stands on top of the retaining barrier, so it was easy to get that one level, and then we worked across the pad. 


I cut some spacer blocks from a scrap of 2" x 4" lumber, so it was easy to get the skids parallel, and then I tacked them in place once each skid was leveled out. 


This is the finished foundation pad with the front and rear rim joists installed. I used the fancy GRK screws to set the lumber in place, and then made sure the structure was square before I shot in more nails than were strictly necessary with cordless dewalt.


We framed out the floor next - we used 2" x 4" doug fir for the floor framing. Normally 2" x 6" is required for flooring, and that's what I used on my last shed, but this is tiny by comparison and we can save two inches on the overall height this way. We stapled on some fine mesh screens in the spaces between the skids - we want plenty of airflow below the shed but hope to exclude non-airbourne matter.


The floor is a sheet of 3/4 inch plywood which was nailed on good an' proper and gives us a very solid base on which to construct the shed. One major advantage of the 8' x 4' footprint is that a lot of the materials can be installed without any cutting.


After all that, was it level - well, yeah, it pretty much was, thanks for asking.


There was bit of Sunday afternoon left over so we cleaned up the yard of leftover bits of cherry tree...


...and converted this pile of de-limbed branches....


...into a pile of firewood - the bigger pieces will need a couple of years to dry out before we can burn them, although it will be closer to five years before we need to given our incredibly low consumption rate. It's actually more important to me to look out of my kitchen window and see neatly chopped firewood than it is to actually burn it.

Saturday, May 16, 2020

Garden Shed part one

Last Spring we built some raised beds in the yard at the side of our house - we put them where they would get the most sun. Over the last few weeks, we've been pulling weeds, digging in manure, tidying up the yard ahead of fire season, and planting our first crops of 2020. 




What we really need is a shed close by where we can store our garden tools and Quinn Sheep's weed wacker. The ideal space for the shed to go is at the bottom of the slope beyond the gates. This is what that section of the yard looked like about three weeks ago when this project was at the "planning" stage.


Moving the wheelbarrow and the compost bins was the easy bit. I also had to get rid of the pile of stone that came from the fireplace remodel - about eight barrows worth actually...


And the some-kind-of-cherry tree. On first glance, this looks like a nice tree, and it does give quite a bit of shade to this part of the yard.


But it is also over-mature - the tree has been savagely pruned a number of times in the past, and most of what is left is trunk - the photo below was taken before I fired up my chainsaw:


This one was taken after about an hours' worth of work trimming off the lower branches and dragging them out of the way:


I've had a lot of teething troubles with the husqvarna chainsaw, but this time around I got it set up properly and it worked very consistently. It is a genuinely nice piece of kit - I spent plenty of $$$ and ended up with a professional tool that I like a lot.

The low-hanging branches were quite easy, but there was still plenty of tree left:


This is the situation after another round of cutting from a couple of rungs up the step ladder. It is worth noting that most of what is left is dead branches; probably less than 25% of the tree had leaves on it. This was where Amy Sheep started to wonder if the tree might not be "a bit too f$%king big" to do ourselves. We still had about twenty-five feet of tree to deal with and we didn't want to bring it down on top of the fence or our neighbor's roof. 


I still thought we could manage it, as long as I could find someone else to climb up the tree and attach the rope....


...and then pull on it while I re-launched my chainsaw-based attack from the top of our wobbly step ladder. Taking pictures during this operation would have been asking for trouble, however it proved successful the first time, so we rinsed and repeated....


Which left us with about ten feet of trunk to deal with:


And that was obviously no match for the husqvarna 450.


Yes, I win!! This was very satisfying because I have never really used a chainsaw before and I've never been project manager when felling a tree before either. I helped my Dad's friend Elvis take out a whole bunch of trees, but he knew what he was doing. I always think where there's a will, there's a way, and it's an attitude that's served me well. Except when I can't be arsed to do something....


Stacked up the bricks out of the way...


Our tool shed will be going in this space soon:


Before that, we have a huge pile of trimmings to deal with...


And a LOT of firewood to chop up!


To be continued....