Showing posts with label display case. Show all posts
Showing posts with label display case. Show all posts

Friday, July 17, 2026

Table Saw Room Refinements Part 3

At the beginning of May I built some display cases in the table saw room. Since then, I have mostly been sorting through LEGO and working on one or two other projects, but I have also been making progress here too. 

My main concerns for covering the display cases are cost, durability and the perimeter seal, so I'm going with acrylic panels which I can hold in place with a few screws.  I had the panels cut to size at TAP Plastics in El Cerrito, and I drilled the holes myself. I actually bought a special drill bit for use with plastics, but I managed to break it after just a couple of holes; fortunately, a regular drill bit, on a slow setting, worked fine.

I installed self-adhesive "furry" weather-stripping at the perimeter of each cabinet. I am hoping this will contribute to a dust-tight seal. 


Proof of concept:

Once I was happy with the fit of the first panel, I went into mass production mode and banged out the other five.


The two far left cabinets are going to have doors in due course and will be used for storage.


At this point I have four cabinets filled with LEGO and one other cabinet of "collectables." It is easier to take photos of the contents without the panels. I will be looking at installing LED lighting in some of the cabinets in the future. The eighth cabinet is looking like it will be storage for the time being.





Sunday, July 5, 2026

The LEGO Room

I loved LEGO when I was a child, and I was quite old when my collection was boxed up and consigned to the attic. After that I can't say that I thought about it very much until Samuel Sheep was gifted his very first LEGO in around 2010. It was this Buzz Lightyear set if you're interested, and it came along courtesy of Paul Circus. It wasn't immediate, but Samuel Sheep developed a deep appreciation of LEGO, and I was reinvigorated by the adult-themed sets which were becoming very popular at the time.

Fast forward to Spring this year and we have a bunch of models gathering dust (see below) and a huge pile of plastic boxes filled with LEGO. None of the little sheep could care less about LEGO at this point so I have been quietly establishing outright ownership.


I've always wanted to display some of my favorite models in the workshop/man cave, and now I have the cabinets I built here.


The only problem with this plan is that all the assembled models have a few - or quite a few - missing pieces. This is because the collection was never meant to be a work of art and has been extensively "played with." Still, if you're going to display something, it should be complete or close to complete. I've been around LEGO long enough to know that looking for a few particular pieces in a big collection is a futile operation.

It was obvious that if I was going to find the pieces I needed, some serious sorting out was required. What happened next is another excellent example of "project creep." After a whole week of sorting piles of LEGO in the evenings, while watching TV, I realized that (a) this was going to take quite a while and (b) I didn't know what I was going to do with all this neatly sorted LEGO. I had to go big or go home.

So, I went BIG. I moved the sorting area to a 4' x 8' sheet of plywood on top of the table saw, so I had plenty of space to work in and did not need to tidy up after myself in between bouts of sorting.

This....

...went on....

for days....

...luckily, I had help

Eventually I ended up with a pile of boxes in the basement, each of which was filled with many small plastic bags of individual parts.


Before all this started, the LEGO was stored at the lower section of what was our "games and puzzles closet" in the same plastic boxes. In future, this area will be known as the Lego Room.

The first step was to empty the closet of everything that isn't an IKEA shelving unit. Then I removed the middle 2x4 black unit and lowered the horizontal 1x4:

This is after taking the vertical 1x4 unit over to the workshop and converting it into a 1x3 which, thanks to careful measuring, is now exactly the same height as the two other units combined. The two (2) white cabinets were attached to the wall in preparation for the Big One; this configuration traps the black unit so it does not need fasteners.


I made a very swish countertop by slicing up the top panel from an old dining table and attached it to the cabinets with double-sided foam tape. This will make a very nice work surface and took less than ten minutes to cut and install. It also goes to prove that not everything has be glued and screwed.


Hung the first batch of parts cabinets and set the hardware for the ones that haven't been delivered yet.

While all this has been going on I have been considering how best to sort/classify the various LEGO parts. Not wanting to reinvent the wheel, I reached out to my bestest friend, the interwebs, and copied the hard work of The Brick Architect. This website includes an easy-to-follow labeling system which incorporates diagrams of every piece:


Self-adhesive labels can be cut out wit' tut sithers, an' stuck ontut parts dooins drawers:


Phase #1 is getting my sorted parts into correctly labelled drawers:

Phase #2 is organizing the drawers into the same order as the The Brick Architect's parts catalogue:


Plenty of distribution still to do:


I got a bunch of much larger drawers for the most common parts:


Some of the large drawers were subdivided to make the best use of space:


This is a couple of weeks later after the second batch of parts drawers have been hung. It was about now that I realized I was going to need more drawers.


Added two (2) more cabinets at each side of the closet for a total of 12, which gives me 576 of the small drawers and 72 of the larger ones at the bottom of the lower cabinets. I also have 18 of the really big drawers. It's worth noting that a lot of the smaller drawers contain two different parts, so I easily have more than 1000 different parts in my collection. 

I basically got the last four cabinets for free because I was planning to buy this piece of artwork to hang in the LEGO room, and now I don't have room for it. Thus, the cabinets were paid for with money I had already mentally spent. Yay!


This is how the room came out as photographed without a fish-eye lens: 


I found a jpeg of this vintage artwork on the internet and printed it out to use as a door sign.


I got these "lego-compatible" cover plates for inside the LEGO room:


The next project is to find another home for all of the stuff which has been displaced...

Monday, May 4, 2026

Table Saw Room Refinements Part 2

The real focus of this post is the cabinets I mentioned a few weeks ago. But before that, I have some insulating to do. For some context, the exterior deck/garage ceiling also extends over a small section of the cabinet saw room. I had a lot of small pieces of OSB sheathing left over from insulating the garage ceiling, so I bought some more insulation material and got stuck in.


I'm covering up several electrical junction boxes, so I was sure to mark the appropriate panels with red tape. This way I'll know which panels to remove if I ever need to get at any of the electrical.


All done. I'm not looking to add structural support to this area, so I was able to make use of a lot of what would otherwise have been scrap OSB sheathing.


Put the lights back:


Now onto the real business. This is how the table saw room looks after I installed a timber shelf/platform and wall-panel over the somewhat uneven concrete.


Fast forward to the weekend just gone and I picked up some 3/4" Baltic birch plywood on the way home from work. This is expensive material but is also extremely flat and well known for its easy machinability and screw holding strength that’s superior to other plywood options. These qualities mean it is dense material, but that is not a problem for this particular project. You can learn all about Baltic birch plywood here.
 

I spent a couple of hours building my prototype cabinet, and checked that it would fit and look ok.


There is a gap of about 3/4" between the top of the cabinet and the floor joists, in case I want to finish the ceiling in this area, although I think that's unlikely.


Time to go into production! I need a total of eight (8) cabinets, so seven (7) more to make. The plywood sheets are actually too heavy to lift on my own, so the first step is to cut a strip 30-1/4 inches wide off each board using the "track saw."


This piece can then be trimmed to precisely 30 inches wide with the table saw. 


I can just about lift the leftover two-thirds of a panel on my own, and pass it twice through the table saw, so that after almost 45 minutes of hard manual labor, I ended up with a pile of 30" x 48" panels.


The top, bottom and both side panels are all the same size: (30" x 11-7/8"), which means I can cut four, enough for one cabinet, from a 30" x 48" panel, without any waste. 


I've always hated sanding, but it's a necessary evil...


Sanded side panels (14): 


I'm joining the panels with pocket screws. Apart from being quick and cheap, I can take the cabinets apart later if I ever need or want to:


Sanded top and bottom panels with pocket holes bored (14): 


I modified an earlier jig to work with 3/4" plywood:




Assembly is of the "build two halves and then connect" variety. Since all the panels are the same size, I don't have to worry about orientation.  


I checked every cabinet for square before installing the pocket screws.


The inset back panel measures exactly 30" x 28-9/16" because the plywood is actually 23/32" thick instead of the advertised 3/4."


The strength in the cabinets comes from the thickness of the plywood and the excessive number of pocket hole screws which secure the back panel: 


Peg holes were drilled with the Kreg™ jig. I bored three sets of peg holes because most of the shelves will not be the full depth of the cabinets.


I'm assembling the cabinets in batches of two or three because they take up a lot of space in my workshop.


I'm installing the cabinets in the cabinet saw room in two banks of four, starting at the workshop side. I placed and leveled the far-left cabinet first and then aligned the other cabinets with that one.


I used the laser level to help me get the cabinets lined up perfectly.


I left some 3/8-inch gaps between pairs of cabinets to allow the power cords to pass through.


The first three cabinets were straightforward but then I ran into the heating duct... 


I could work around the duct, but instead I am going to redirect it. The first step is to cut out the 90-degree bend:


The old piece is on the right. I will be replacing it with the smaller piece on the left.


I'm installing ducting which consists of a flexible plastic-wrapped core that is sleeved with fiberglass and aluminum foil.


Connection #1: flexible duct to 45-degree elbow with foil tape:


Connection #2: 45-degree elbow to area below vent with A LOT of foil tape:


Connection #3: flexible duct to rigid duct followed by placement of fourth cabinet:


The end cabinets were secured to the base panel/shelf...


...and all cabinets were secured to the floor joists and to each other. I didn't buy any of the brackets for this project, I just used up whatever I had in the shop because ultimately none of them will be visible.


Section one complete. I'll be calling these cabinets the "Left Bank" for identification within the (future) lighting system.


It makes sense (to me) to start installing the right bank at the point where the older part of the building meets the area below the deck, since there is a difference in the height of the ceiling, and then work right to left. 


Two down, two more to go....


After placing and securing all four of the "Right Bank" cabinets, I have a gap at the center:


This is useful since I can still access the 220 Volt outlet for the cabinet saw, but the real purpose of this space is to house the lighting control module and a couple of other things.


I installed a two-inch-wide strip of plywood below the cabinets to cover the imperfect transition to the mounting panel and then I fixed several outlet banks at intervals along the wall.


All cabinets and electrical secured:


I made some shelves from the leftover plywood.


I will be making doors for at least two of the cabinets which will be used for storage. I want to make something a bit more interesting that a plywood door, so I am looking for ideas at the moment. The other cabinets will be used to display some of my collections and will have either glass or polycarbonate panels at the front.


To be continued....