Showing posts with label desks. Show all posts
Showing posts with label desks. Show all posts

Wednesday, March 25, 2020

Fireplace Remodel Day Thirty Three

It's Wednesday and the floors are dry! I'm ready to be done with the living room and move on to the next part of the project....except one thing: Amy Sheep is doing the telimedicine thing in the office, and I can't make noise or potter about in the office or dining room without risking exposure to to the prying eye of her webcam.

So I just had to get on with finishing the cabinet doors quietly as quietly as possible.



After I was happy with the hinge adjustments, I took the doors back off, removed all the hardware and took them back to the workshop for wood filler and final sanding. Then it t'was time for us dinners.


Amy Sheep was still doing her being-professional-thing in the office après le déjeuner, so I went back down to the workshop to look for something to do. About 3 or 4 weeks ago, a friend gave me a display case - it was lying around in a house she was clearing out and would have been trashed if I did't take it. At the time I needed another project like a hole in the head, but the cabinet had potential....so I took it back to my garage where it hasn't moved since that day.....until now that is.

I could not wait to remove the hideous trim pieces, so I don't have a proper "before" photo. This picture was taken after the base had already been ripped off:


That's better - the base and top trim pieces where they belong - in the trash pile.


The trim had to go because (1) it's f&*%ing hideous (see above) and (2) I want to put the display case in the corner of my garage; the foundation sticks out in this area, so I have to accommodate that in the design of my replacement base.


To call it a "design" is probably a bit generous. It's a box made from a scrap of 2" x 6" lumber and a piece of birch plywood which was left over from the cabinet doors


Installed it doesn't look anything special, but it meets the design criteria of hoisting the cabinet above the foundation while allowing it to mount to the wall.


Slapped on a bit of plastic wood.™


I made a replacement top panel from another piece of scrap birch plywood. It wasn't quite large enough, so I glued on some edge pieces I cut from a piece of old bed frame. You have to recycle what you can in these extraordinary times...


I also took out the mirror and all the glass panels and removed all the hardware. When the wood filler is dry, I will sand the cabinet down and paint it....watch this space!


I went back upstairs to put t'ettle on, and found that the day's telimedicine had concluded. After a cup of rosie and one of Ruby Sheep's fluffy cookies, it was finally time to tear down the barrier between the office and the living room....this was a profound moment in the project.


After that it took the best part of two hours to move our office into the living room. The telimedicine terminal and associated AV technology was fully integrated into its new home, all ready for another busy day.


Tomorrow I will return to working on the hardwood floor at the dining room side of the fireplace. I last worked on this area on Day #10. Wish me luck!

Thursday, January 3, 2019

Walnut Desktops

Just to recap, this was the scene before we started the refurb. After getting rid of the sliding door, we needed some new furniture to replace the crap we've been mekin' do wit' for.....well, for donkeys years actually. We figured we could make much better custom desk tops ourselves than we could buy.


We started with two 4' x 8' sheets of walnut veneered ¾" plywood which we cut to size with the jigsaw and squared-up with the router.



Perimeter trim pieces were cut from solid black walnut and mitered at the corners.


The trim was attached with a mixture of biscuits and wood glue.


Multi-stage glue-up. Like Jerry Rosa says, you can never have too many clamps.



The excess walnut trim was removed with a combination of my new Bench Dog smoothing plane and the Dewalt random orbital sander, and the bench tops were sanded to 360 grit.


The underside of each desk top was sectioned with narrow strips of walnut. This will help located the desk tops above the file cabinets. 


We cut cable access openings in both desk tops - fortunately, my first (and favorite) woodwork instructor was on hand to explain how to sharpen a chisel "ba'ht stone."



It's easy with a sharp chisel.

Plugs were fashioned from walnut scraps.

Plug supports were glued in.

The finish was three coats of flat varnish, which had a cure time of twenty-one (21) days.


All cured and installed: