Showing posts with label cabinet saw. Show all posts
Showing posts with label cabinet saw. Show all posts

Wednesday, November 4, 2026

Table Saw Room Refinements Part 4

Earlier this year I built some display cabinets in the table saw room. Some of the cabinets are reserved for storage, and therefore need some doors, otherwise they're just shelves. I've had a few ideas for door designs, but in the end, I decided to return to the concept I came up with for the router table cabinet. This decision means I can make the doors without having to buy any material.

The door frames will be made from red oak. The source of the longer pieces was a hideous 80's TV cabinet that the former owner of my house left behind, and the rest were miscellaneous scraps. I ripped all the bulk material into 1-3/4" wide strips on the table saw. There is some variation in the thickness of oak, so I made pairs of thick and thin strips of similar length. 



Both mating surfaces were planed to remove the old finish, and then wood glue was applied to both sides of the joint:


Everything was clamped overnight:



The glued material is now close to 1-3/4" x 1-1/2".


Face sides and face edges were established at the jointer...


Material was trimmed on the table saw...


And planed on all four sides:


The final dimensions are close to 1-1/2" x 1".


A rabbit which measures 3/4" x 1/4" was cut into the least attractive edge/face:


I figured the easiest way to get all six doors exactly the same size and shape would be to build a jig. The final size of each door is intended to be 30" x 15-1/16", so I constructed a frame that is about six inches longer than that and the exact width:


This is how the jig looks when it has been loaded with the four mitered frame pieces. The fourth side of the jig is installed with two (2) screws, so it can easily be removed. This is important for getting the completed door out of the jig...


I want to dry fit the inset panel before I glue up the frame, so I moved back over to the table saw. I'm making the panels from leftover walnut veneered plywood. I have enough plywood to make the six (6) panels I need, if I ignore the grain pattern. However, the best way to exploit the grain pattern would be to make two pairs of doors....and do something different for the third pair. 


Panel loaded into jig:


After removing all the components, applying glue to the mating surfaces, and reloading the jig, I was ready to install V-nails at the corners of the frame:


I put three V-nails into each corner, and then the door was removed from the jig, and the central panel was clamped to the frame overnight.


The almost finished door looks like the photo below. I need to do some sanding, and I need to make the beading I'm planning to install at the doors.


But, if you've ever read this blog before, you'll already know that I really do not enjoy sanding. So, I moved on to making the final pair of door panels. The concept is basic: the best bits of the remaining walnut plywood separated with some 3/4" wide strips of maple:


The panels were glued-up overnight:


After trimming and sanding off glue residue (below). The outer walnut strips were cut slightly wider than the inner pair. This is because the perimeter of the panel will be obscured by a combination of the edge of the oak frame and the beading; the strips should appear to be of identical width when the door is assembled.


These frames were constructed just like the others, and the panels were glued and clamped overnight:


The last thing to make is the beading, which comes from more scrap red oak. To start with I cut a bunch of 5/16" square strips on the table saw: 


To shape the beading I am using a 3/8" coving bit on the router table, but the size of the red oak stock is too small to pass it safely across the bit..


I cut a 5/16" square recess into a piece of scrap plywood...


..and clamped it in front of the router bit. I can now feed my material through the gap in relative safety:


A total of four passes across the router table were needed to achieve the profile below which is not symmetrical by design. 


As mentioned, the beading is 5/16" wide, but the recess it will be going into is only 1/4" deep. This means that there is 1/16" of material to sand off after the beading is installed. It also means that the profile of the beading will end up being symmetrical or pretty close to it. This overall process gives a much better result than trying to cut beading to 1/4" square in the first instance.


Post beading install, sanding, wood filler, final sanding, more sanding etc.


Finishing with Danish oil, starting with the back of each door:


Fronts finished:


Each door needs six (6) small holes for the hinges and one (1) 3/16" diameter hole for the pull. I made some jigs out of scrap plywood which made this process quick, easy and accurate: 


Cabinet doors installed: 



The big picture:

Saturday, September 12, 2026

Bedroom Dresser Part 4

The reason this episode of the dresser build is dropping so quickly after part three is that most of the work in this post was done at the same time as I was building the frame. This time I'm focusing on the last remaining major part of the build: false fronts for the drawers. The starting point for each "front" is a piece of 3/4" maple veneered plywood and a selection of 3/4" wide by 1/8" thick maple veneer:



The fronts are all the same overall size (20-7/8" x 5-15/16") but have two different styles. The four lower drawers are the simple ones: A plywood panel which measures around 1/4" less in each direction than the final size is wrapped with 1/8" maple veneer....and that's it for embellishments.


After glue-up and basic sanding the false fronts were trimmed again to eliminate any variations in the thickness of the veneer:


The repeated application of maple wood filler and sanding to 220 grit was followed by staining with the same 1:1 mixture of English chestnut and gunstock used on the cabinet. Looking pretty good, right?


While the fronts were great, the edges were a different story because marks from the circular saw blade were evident throughout:


To deal with this unexpected issue the edges were sanded to 80 grit to get to the bottom of the indentations and then to 220....


....and the stain was reapplied. I did this for all four edges of each drawer front, and then they were finally ready for installation.


The eight upper drawer fronts are more complicated. The embossed style dictates that the starting material needs to be 1/8" thinner than the lower fronts. Running the plywood panels through the planer is the simple solution to this issue, but the drawback is that the veneer is lost from one side of the plywood:

As previously mentioned, I wanted the plywood to be undetectable, and I came up with a labor intensive but unusual way of doing that. I actually trimmed the plywood down to 1/2" thick, so 1/4" or 2x pieces of 1/8" thick veneer away from what I actually want. The perimeter of each panel was then wrapped in maple veneer as above 

I'm making up 1/8" of the thickness with strips of maple veneer installed at the perimeter of the rear-facing side of the drawer fronts - the veneered edge is the only portion which will be visible when the drawers are assembled, so the central area of each panel was padded out with bits of scrap material of the same thickness:


The front face is treated with the same maple veneer as above except the corners have been mitered. These pieces of veneer were stained ahead of the install and any tooth marked sections were either turned over, sanded or discarded. 


I used wood filler made from fine maple sawdust and wood glue, followed by sanding, to eliminate any gaps in the veneer....


....and applied wood stain:


There were no unexpected teeth marks this time around, but the stain did highlight some stray blobs of wood glue, which were removed by light sanding and the areas re-stained.


Staining the drawer boxes was a two-step process which began with applying stain to the veneer at the top edge.


Any imperfections that came to light in step one were dealt with and then the inside of the drawer and the two outer side panels were stained. I didn't bother staining the front, since it will be covered, or the back or underside, since these areas will not be visible.


At this point I have twelve drawer boxes in two sizes and twelve drawer fronts in two styles. I also have the cabinet and the frame which I made earlier. Stay tuned for the final assembly!