Saturday, January 6, 2024

Dining Room Cabinets & Bookcase Part 2

When I left off, some time ago now, the bulk of the cabinet had been glued up:


The next steps are to install the top panel and the plinth/kick panel. I started with the latter which had already been cut to the correct width and veneered at one end. With the cabinet glued-up, I can measure the exact length I need for the plinth. I made the cut after subtracting an additional 1/8 of an inch. 
 

The addition of my home made walnut veneer at the cut end brings the length back to the correct amount.


Plinth/kick panel installed:


With that done, the top panel was precisely aligned and clamped.


The top panel and the five upright panels were marked with tape and then slots were cut with the biscuit joiner at the marked locations: 


After that, the top panel was glued up and clamped overnight:


The next day the cabinet was placed face-down and a 3/4 inch deep x 1/2 inch wide rabbit was cut at the rear edge at the cabinet with the handheld router. 


Some sections could not be removed with the rabbiting bit and required an olde fashioned hammer and freshly sharpened chisel:


All done:


This was the point at which this project went on hiatus. While the sun was shining my "workshop time" was devoted to working on the deck project, and then we went out of state for the Christmas holidays.  I returned to the cabinet just before new year - it was pouring with rain at the time so there was no opportunity to work on the deck.

Cut a slightly oversize piece of plywood for the back panel:


After trimming the panel is a very snug fit:


I went with rounded corners this time:


Applied tape to the inside of the back panel and marked where to cut biscuit slots:


All slots cut in the back panel....


...And the cabinet:


The back panel was glued up and clamped and left for a day or two:


This is a few days later after the clamps have been removed and the cabinet has been turned the correct way up. The next step is to construct the face frames and cabinet doors.


To be continued....

Wednesday, January 3, 2024

Fixin' The Deck Part 8

It was a beautiful mid-December Saturday morning, and Amy and all the little Sheep were elsewhere. Not at the time of writing, obviously, but at the time of doing! Outside on the deck there was a gentle breeze and very little background noise at all. So, I went back inside the house and collected my new cordless power planer:


Work so far has mainly consisted of adding shims to the deck substructure....

...and making repairs to the damaged sections:

I'm at the point now where I need to switch to removing material rather than adding it....and this means I need a new power tool! There's not much I don't have at this point, but a power plane is one of those few things. I had to recess the nails with a large punch before I could get to work with the plane:


I'm working my way out to the far corner, which means I am going through the process of lifting more sections of plywood....

had to remove these nails myself...

...and planing down the substructure, a couple of joists at a time. The corner is the low point, so there was a lot of material to remove:


Not to mention significant repairs to the area where the corner post was located: 

before...

....after

Once the repair was complete, I was able to advance the decking to the corner. 


After that it was more planing...


...advancing the decking and more planing....


Where there was more than half an inch to plane off, I made cuts with the circular saw and followed up with either a hammer and chisel or just a hammer before I came back with the plane:


Discovered some more damage at the rim joist:


Brought the upper edge down to the correct position:


Cut out all the rotten wood. 


Filled-in the void the next morning. I've been lucky that we have had almost ten dry days in a row while this portion of the work has been going on. 

More planing while the sun shines...


Getting closer to the last bit or the old roof:


Made it! I have been installing the boards with just one or two screws, so they will for sure have to come up again to be caulked and properly installed. For now, I have to cover up the gap between the new deck and the old roof and prepare for rain...


Layers of plywood and caulk installed....fingers crossed!


To be continued....

Saturday, December 30, 2023

The Christmas Cake

My Mother used to make her own Christmas cakes; usually two, one with icing and marzipan and one that was decorated with nuts and cherries. The former was always my favorite. This year I decided to make my own cake using the tried and trusted family recipe. I typed it out below if anyone wants to try it out; I worked from a photocopy of my Mum's recipe notebook.


I started blending the butter and brown sugar by hand, but it was too much like hard work, so I broke out the electric mixer...


Added eggs, flour, dried fruit etc.


Greased my tin. It is not necessary to use butter wrappers, but it is traditional in my family.


Bake in the center of your oven for three (3) hours at 300 F/150 C/GM #2.


Allow to cool to room temperature before turning out the cake:


It is traditional to store the cake for several weeks in an appropriate tin before finishing:

My cake was left in the cabinet for about three (3) weeks after it was baked. The next step is to apply the marzipan. My Grandmother used to make her own marzipan; mine came premade. It is necessary to knead the marzipan for a minute or so and then roll it out; icing/powdered sugar is useful here to prevent the marzipan from sticking to the cutting board.


I took half a jar of apricot jam, added a tablespoon of water and heated the mixture on the stove until it boiled. The boiling step prevents the jam and sugar from fermenting. The residue was strained with a fine sieve:


The apricot slurry is then brushed over the cake - without this step the marzipan will not stick to the cake. 

After applying the marzipan the cake is returned to storage.


A few days later the marzipan was hardened and ready for icing, so I transferred the cake to a cutting board. If I do this again, I will buy a proper cake stand with a cover and use that.

The icing is made by gradually adding four (4) cups of powdered sugar to three (3) whipped egg whites. Sieving the powdered sugar before mixing gets rid of those tiny annoying lumps. 


This gives icing which is easy to apply and sets very hard. Any excess can be applied to cookies or even digestive biscuits if you have some on hand.


I was planning to add decorations and some additional piped embellishments to the icing, but unfortunately, I ran out of time before Christmas, so the cake was served somewhat unfinished, on a cutting board:


It came out OK. The cake was overbaked and dry, but the other bits tasted great!


For the cake:

8 oz butter
8 oz brown sugar
9 oz all purpose/plain flour
5x eggs
8 oz currants
8 oz sultanas/golden raisins
2 oz glacé cherries
2 oz candied citrus peel
2 oz ground almonds
½ tspn gravy browning
pinch of salt
½ tspn nutmeg

Cream the butter and sugar. Add eggs one at a time. Add flour and other ingredients. Bake at 150 C/ 300 F or GM #2 for three (3) hours. Store for at least twenty-eight (28) days prior to consumption. During this period the cake may be finished with marzipan and icing/frosting as above or may be served as is with cheddar cheese.

For the marzipan:

2x 7 oz blocks of marzipan
½ jar apricot jam

For the icing:

4x cups of powdered/icing sugar
3x egg whites